-->

Ryobi Lawn Mower Troubleshooting

- June 03, 2018
The Ryobi lawnmower can be a self-propelled mower using a 48-volt battery that will adjust in height from 1.five inches to four inches for a variety of grass lengths and surfaces. The battery is rechargeable and reduces noise and beginning issues -- and is far more environmentally friendly than standard gas lawnmowers. Even so, for each of the positive aspects in the Ryobi lawnmower, some difficulties might arise sometimes throughout use that owners will need to have to troubleshoot.
Ryobi Lawn Mower Troubleshooting

Ryobi Lawn Mower Troubleshooting


Adjust Handle Assembly



  1. Adjust the handle assembly when the Ryobi mower handle isn't in the proper height, by loosening the knobs on every single side in the handle inside a counterclockwise motion.
  2. Pull the upper handle up and back to lift up around the handle for the preferred height, making sure the handle snaps into the subsequent place firmly.
  3. Tighten the handle knobs on every single side on the handle inside a clockwise path to safe, making sure the carriage bolts are seated properly.
  4. Don't pull or trap any on the cables in to the handle when altering the handle height.


Recharge the Battery



  1. Recharge the battery when the mower won't commence -- or stops all of a sudden even though operating. Remove the mower fuse key in the slot around the motor assembly and open the battery cover.
  2. Plug the incorporated charger connector cord in to the connection around the mower battery along with the other finish into a 120-volt electrical outlet.
  3. Wait to make sure the red light around the charger illuminates to indicate correct charging -- and wait for the red light to go out just before disconnecting the battery, which can take from ten to 12 hours.
  4. Remove the connector cord when charging is total, and close the battery cover firmly. Note that the battery could be replaced when the battery is broken or no longer charges.


Readjust the Blade



  1. Readjust the blade height when the mower just isn't cutting grass as anticipated. The blade must be set to ensure that the lawn is around 1 to two inches in height in a cool climate, and in between two and three inches higher throughout the warm climate.
  2. Raise the blade height as required by holding the height-adjustment lever around the side from the mower, and sliding the lever toward the rear in the mower. Raise the cutting height when the mower is hard to push, the mower just isn't bagging grass cuttings appropriately or the motor stops although cutting along with the battery has been charged totally.
  3. Reduced the blade height as required by moving the height-adjustment lever toward the front.


Adjust the Blade



  1. Alter the blade when the mower is vibrating at a greater speed than typical. Remove the fuse key in the mower and wait for the blade to quit completely, then remove the battery cover and take out the battery pack.
  2. Tip the mower more than and lay the mower down around the side, setting a block of wood among the blade along with the motor deck.
  3. Use a 15-mm wrench to loosen the blade nut within a counterclockwise motion in the bottom on the mower -- and take out the blade nut, the spacer, the blade insulator along with the blade and set all elements aside.
  4. Push the fan assembly against the motor shaft and slide a brand new blade around the shaft using the two blade posts connected to the holes around the blade. The curved ends must point up, together with the blade flat against the fan assembly.
  5. Reconnect the blade nut inside a clockwise motion having a torque wrench and after that replace the insulator and spacer.

See also:

Can I Turn My Lawnmower Into a Mulching Mower?
How to Adjust Poulan Riding Lawnmower Decks
How A lot Oil Does a Troy-Bilt Mower Pony Take?
How you can Replace the Belt on a Kubota Mower Deck
Ryobi Lawn Mower Troubleshooting

 

Start typing and press Enter to search